A player sends a photograph of a chip on an edgeless rim. The chip is about the size of a grain of rice, and he asks whether the warranty covers it. The warranty page covers this case in one line. Chips to the top or sides of edgeless paddles are excluded.
The same site sells a tape for that edge at USD 8 a pack, read on 29 October 2026. The pack holds three strips, and the strips come in three widths.
The two facts belong together, and reading them apart misses the decision behind both. The company takes a failure out of its warranty, and it sells a part for that same failure. Those two moves together decide who carries the cost. For a brand building its own line, that pattern is worth copying or rejecting on purpose rather than by accident.
The tape page also shows something a catalog usually hides. It ties each width to a named set of models. Together the three add up to a list of the guard profiles the company builds. That list is where this article starts.
Three widths, and the line behind them
Width | Models the page names | Core those models carry |
15 mm | LABS Project 007, edgeless paddles of 10 to 14 mm, guards thinner than 10 mm | 10 to 14 mm |
20 mm | Power Air, SLK Omega, LABS 005 | 13 mm on the Power Air |
30 mm | LUXX Control Air, LABS Project 003 | 19 mm on the LUXX |
The three widths do not climb with the core in a straight line, and two models on that list show why. A 13 mm Power Air takes the 20 mm tape. An edgeless paddle of 10 to 14 mm takes the 15 mm one. If the width followed thickness, those two models would swap places.
The width follows the guard. A guard laps onto the face, so the strip has to cover that lap and still land flat on both faces. An edgeless build has no lap, because the faces meet the core at the rim. A narrow strip is all it can take.
Read that way, the three widths are a factory document. They say this company runs at least three guard profiles, and the tape list is the cheapest place to see it. A brand that runs one profile needs one tape and stops there.
Why an edgeless rim chips and a guarded one does not
A guard spreads a hit across a band of plastic. The width of that band decides how much of the hit reaches the laminate. When a paddle scrapes the court, the guard takes the load and passes only a share of it inward.
An edgeless paddle has nothing in front of the rim, because the two faces meet the core at the edge. That joint is all that stands between a scrape and the inside of the paddle. A hit that a guard would spread over 20 mm lands on a line the thickness of a face sheet.
This is why the warranty stops at the rim of an edgeless paddle. A chip on a guarded edge points at the guard, and a guard that fails early is a manufacturing fault. A chip on an edgeless rim points at the hit itself, and no factory can promise a rim against a court.
The exclusion is honest, because a rim has no guard in front of it. The player pays for it at checkout instead. A brand that sells an edgeless paddle has to say so before the sale. The complaint always arrives after it.
Two ways to close an edge
A brand picks one of two builds before it picks a supplier, and the choice decides where the chip cost lands. The table below sets the two side by side. One column puts the edge in the bill of materials, and the other puts it in a retail listing.
| Guard molded onto the plate | Guard as a part, strip on top |
Where the cost lands | Bill of materials, on every unit | Bill of materials for the guard, retail for the strip |
Who carries a chip | The brand, if the guard fails early | The player, as wear |
Can the edge be replaced | No, the guard is the paddle | Yes, the strip lifts off |
Tooling | One mold per profile | One mold per profile, plus strips in each width |
The left column is the build we run, and it is what this article means by a molded guard. The guard is molded onto the plate under heat and pressure. That is why a new profile carries a 10-day tooling lead.
The right column is not a cheaper version of the left one, because it moves a failure rather than removing it. One failure leaves the warranty and becomes a consumable that the player buys. A brand can put a strip in every carton. That buys the failure back at cost, on every unit. A brand that sells the strip separately has turned it into a second product.
Neither choice is wrong, and each one needs a warranty that matches it. A brand can pick the right column and still write a warranty that promises the left one. That mismatch is where a claim turns into an argument.
Where our 3.2 mm goes, and where it does not
Our guard laps 3.2 mm onto the face, and the outermost 2 mm of that lap carries no ink. The adhesive grips bare material instead of printed film, which is what keeps a bond from lifting in the first month.
That 3.2 mm is not a tape width, and the two numbers should never share a table. The lap is how far the guard reaches onto the face. A tape width is a separate measurement. The band it wraps onto each face works out from the strip width and the edge thickness.
A buyer comparing a guard spec against a tape listing is comparing two different parts of the same edge. The lap belongs in a drawing, and the tape width belongs in a parts list.
What a strip in the carton does to the claim rate
The pack holds three strips, and a strip is a consumable. The edge marks up on every court scrape, so the count matters as much as the price. A buyer should read the pack against a season rather than one replacement.
For a brand, the carton is where the cost lands. A strip inside the box arrives before the complaint, and it costs one line in the bill of materials. A strip sold at retail arrives after the complaint, and it carries its own stock, listing and freight.
The first route lowers claims and raises unit cost. The second route raises revenue on the customers who care and leaves the rest to file a complaint. A brand with a one-year term has less to gain from the first route. The complaint window closes before the wear shows.
Whichever route you take, the strip has to match the guard. A strip cut for a 20 mm profile will not sit flat on a 15 mm guard. A customer who has to trim one by hand will trim it badly.
What we do not claim
We do not know how many chips its warranty team turns down. No page and no retailer publishes the number, so we will not fill that gap with a guess. The only figures in this article are the ones printed on its own pages.
We do not claim a molded guard ends edge complaints. It moves them, because a guard can still lift at the lap, and that failure is ours rather than the player’s.
We cannot tell you why it picked three widths rather than two or four. The page names the models and stops there, and the thinking behind the split stays inside the company.
FAQ
Does the tape repair a chip that has already happened?
No. A strip sits on top of the guard and takes new scrapes. A chip that has already opened the rim is a repair job, and the warranty page answers it with an exclusion rather than a fix.
Which width fits a 16 mm paddle?
The page names no 16 mm model in its three lists, so a 16 mm build has no recommended width from the maker. Measure the guard profile instead, then pick the strip that covers the lap and still lands flat on both faces.
Is the tape structural?
No. The guard underneath closes the edge, and the strip covers the guard. That is why a lifted strip is a cosmetic case rather than a scrap paddle, as long as the lap under it holds.
Can a brand sell its own edge strip?
Yes, and the width has to follow the guard rather than the core. A brand running one guard profile needs one width. A brand that changes the profile with every thickness ends up with a parts list as long as this one.
What does a molded guard add per paddle?
It adds tooling, and the profile decides how much. A guard molded onto the plate needs one mold per profile, and a change of profile adds about 10 days before the first sample exists. The material itself is a small line next to that.
If you are building an edge now, start from the profile rather than the tape. Where a guard is molded onto the plate covers the build we run, and how an edgeless edge behaves over a season covers the other choice. The six-spec comparison shows how the guard and the thickness move together. When the drawing is ready, send your guard drawing and we will quote the profile and the strips against it.