The lowest price on the Selkirk line is USD 80, for an SLK Helix Pro, and the highest is USD 333. Both prices were read on 30 October 2026. The gap between them is 4.2 times, and both paddles carry the same brand name.
A buyer who wants to sell at the expensive end reads that gap as a list of parts to add. Four parts separate the most expensive model from the rest of the line, and one of the four takes something away. The weights that give the flagship its stability clamp onto the edge guard. That leaves no flat band for the strip of tape most paddles carry there.
The four parts are listed on the four additions on its own product page. Each part asks something different of the plant that builds it. The sections below take them one at a time, in the order a build takes shape.
Four parts, and what each one asks of the plant
| Part | What it is | What it asks of the plant |
| BoomCore | A foam block inside an EVA ring | A foam mix and a mold of its own |
| MOI weights | Small clamps on the edge guard | A guard cut to seat each clamp |
| InfiniGrit face | A coated surface on the carbon face | A wear test to back the 3x figure |
| Limited lifetime | A term in the contract | A material list that stays frozen |
Three of the four show up in the sample box. The fourth is a clause in the contract, and it decides which foam you can still buy in year three. A brand that picks the term before the parts has to re-test every part it changes afterwards.
That order matters for a buyer, because the first three can be quoted from a drawing. The term cannot be quoted until the rest of the build stops moving. The quote therefore arrives in two passes, and the second pass waits on the foam.
Why a foam core needs a new press trial
A honeycomb core is cut from a sheet that arrives at its own thickness. The density comes with the sheet, so a new core height means a new sheet order. A foam core is poured into a mold at a set density. A new density therefore needs a new press trial before anyone sees a sample.
The BoomCore puts two parts in that mold. A foam block sits inside an EVA ring, and the ring carries load around the foam. A 16 mm core holds 1.20 liters, which comes to 96 grams at 80 grams per liter.
The EVA ring is the part that holds the edge up. Foam alone bends under a hard hit, so the face sinks near the rim and the sweet spot shrinks. The page on nine cores and faces compared sets out the foam families and what each one does.
The company also sells a no-core-crush line. That claim comes from the material rather than from the brand. A honeycomb wall buckles and stays bent, and foam has no wall to buckle.
Where the clamps leave no room for tape
The MOI weights are small clamps, and they hold onto the edge guard. The guard therefore has to run flat along its length. It also has to stay stiff enough to hold a clamp under a hit.
A strip of tape needs that same flat band. A paddle with clamps has no band left. The page recommends no edge tape for this model, and nothing on the page explains that recommendation. A clamp and a strip both need that band, so the recommendation reads as a fit problem rather than a rule. The note on why a strip cannot go on every edge covers how each width behaves on a given guard.
Two lines on the warranty page show what that clamp design costs the buyer. The covered list names a loose edge guard and cracking. The excluded list names damage from hits to the ground.
The part that carries the weights is also the part that takes the ground hits. When a clamp works loose after a hard scrape, the term covers the loose guard and not the scrape. A brand that copies the design inherits that split as well.
The guard is also a place to put mass, which is why a clamp lands there. Our guards lap 3.2 mm onto each face. That lap is what lets a molded guard take a load instead of resting on the face.
Why one core gives two swing weights
| Widebody | Elongated | |
| Height × width | 15.95 × 8.00 in | 16.50 × 7.45 in |
| Average weight | 8.0 to 8.4 oz | 8.0 to 8.3 oz |
| Average swing weight | 112 | 118 |
| Average twist weight | 8.2 | 7.2 |
| Grip length | 5.6 in | 5.8 in |
Both shapes were read off the product page on 30 October 2026. They carry the same core, the same face and the same clamp system. The numbers still land six points apart on swing weight. The two shapes also land a full point apart on twist weight, which is 8.2 against 7.2.
Twist weight is what the mass does across a shape, so you cannot order it as a part. A wide face puts mass further from the center line, and that is where the extra 1.0 comes from. The widebody reports a swing weight of 112 against 118 on the longer shape. The shorter body turns over faster.
For a buyer, this means the number follows the shape you draw rather than the parts you buy. A factory can press one core and ship two very different paddles from it. The two spec sheets will look like two designs.
A 3x spin claim needs a test you can repeat
The face carries a coating, and the page puts it at up to 2,000 RPM. It also claims three times the durability of a raw carbon face. The page names the baseline, which is an embossed peel-ply raw carbon surface, but it does not name the test.
Three times is a ratio, and a ratio needs two measurements taken on one machine. A wear test takes a fixed abrasive, a fixed number of cycles and a spin reading before and after. Without those three, the claim is a sentence on a page that a buyer cannot check against a sample.
We use one rule for claims like this one. We quote the number we can reproduce on our own rig, and we say which rig it was. When a buyer asks for 3x, we ask for cycles and abrasive grade first.
A lifetime term across a plant move
The fourth addition is the term. This one is limited lifetime for the original purchaser in the United States. Replacement paddles carry no new term. The company also decides whether a paddle is covered and whether to repair or replace it.
The page also covers the origin stamp. The company moved to a larger plant in July 2026 and promised the same specs. New units carry a different stamp from older ones, and the page tells buyers so.
One lifetime promise now covers output from two plants. No page tells you which plant made your paddle. A brand that copies the term faces the same gap in its own records. The promise follows the model, and the records behind it have to follow the plant.
We would still write the term, and we would keep the plant record beside it. The first claim will ask for it, and by then the record has to exist. That record starts at the press, and it settles a claim in one look.
Where copying this build goes wrong
The guard is where the first decision lands. A guard cut to seat a clamp is a new tool at our plant. That tool adds 10 days before the first sample exists. A brand that wants the weights without a new tool can mold a plain guard and keep the tape.
Two shapes from one core is the cheapest of the four to copy. One core mold and two sets of plates give a range two swing weights. That is how two paddles at very different prices share one press.
We would not copy a lifetime term across a plant move without a re-test. The term freezes the material list, and a second plant adds a second list to the same promise. A buyer who skips that step pays for it at year four, when the paddle comes back.
We would not print a durability multiple unless the same test had run on our own rig first. A number a buyer cannot check gets checked somewhere else, and that check usually happens after a failure. The six-spec comparison sets out how a core choice limits the guard and the weight.
A 16 mm foam core takes 96 grams of a 225 gram paddle. The other 129 grams cover the faces, the guard, the handle and the weights. That budget is where the four parts fight each other, and the fight starts with the guard.
What buyers ask before they order
Is the Boomstik core foam or honeycomb?
The core is foam inside an EVA ring, and both shapes use a 16 mm core. The foam carries most of the volume and the ring carries load around the rim.
Is edge tape recommended for this paddle?
It is not recommended on this model, because the perimeter weights clamp onto the edge guard and take that band. A strip of tape needs the same flat band. The guard still takes the scrapes, and the term covers a loose guard rather than a ground hit.
Can we build a 16 mm foam core at 225 grams?
A 16 mm core holds 1.20 liters, so 96 grams of foam leaves 129 grams for the rest of the build. That figure assumes 80 grams per liter. A lighter core needs a lower density and a fresh press trial.
Does a lifetime term cover a paddle made at the old plant?
The page names the original purchaser and the United States, and it does not name a plant. Nobody outside the company can confirm how a claim from the older plant is handled. A buyer should get that in writing before the first order.
Does any of the four parts need new tooling?
The guard needs new tooling if it has to seat a clamp. The core needs a new trial if the density changes. The coated face is a process step on the existing line, and the term is a clause rather than a part.
Four parts run through one sample box and one contract. A brand that copies all four buys a paddle it can sell at the expensive end of a range. It also buys a guard it can no longer patch. When your build is set, send your build sheet and we will quote the guard tool and the test layer.